注册 登录  
 加关注
   显示下一条  |  关闭
温馨提示!由于新浪微博认证机制调整,您的新浪微博帐号绑定已过期,请重新绑定!立即重新绑定新浪微博》  |  关闭

杭州溜冰鞋

联系人:翁利文 QQ:85111570 手机:13758243050

 
 
 

日志

 
 

How to test the temperature of the oil bearing  

2013-10-17 09:56:34|  分类: 默认分类 |  标签: |举报 |字号 订阅

  下载LOFTER 我的照片书  |
一.TIMKEN轴承温度高的原因:
    (1).在运行机器的时候,送往到KOYO轴承的冷水没有连接好。
(2).用的油本身的质量就不好,油里面所含的东西不干净或者是运行中出现的油劣化,油中带有的水增加时会直接引起油里面带有的东西也涨起来,这样可能会直接降低油的光滑作用,从而使转轴遭受到破坏,也就造成FAG轴承温度升高。
A . TIMKEN bearings high temperature causes:
    ( 1 ) In the running of the machine when the water rushed into KOYO bearings not properly connected.
    ( 2 ) . Use oil itself, the quality is bad , the oil contained inside something is not clean or oil degradation occurred in operation , the oil increases with the water will be directly caused by the oil inside the thing up with up , this may directly reduce oil smooth effect, so that the shaft suffered damage, thus causing FAG bearings temperature rise.
二.怎样去处理 
    1、检查冷水所用的表,水流及管道是不是顺畅。若水压过低就有可能是过滤网堵上了,如果不能及时的去处理的话,就会使机器出现事情。
    2、应该要定期的测验NSK轴承油压的位置,如果发现油压过于低的话就有可能会导致冷水的门关闭。
    3、用一个小勺取出一点油来,仔细的观察下油的颜色有没有发生变化,然后在把它拿给研究人员做一个测验看看有没有变质。如果发现有不好的地方,应该及时停下机器更换新的油,如果在运转下去,就会给机器带来很严重的破坏了。
4、检查油位是不是在正常的位置上,如果有不正常的地方,然后再去检查油门有没有关紧。如果已经关紧了,应该在补点油,以防不够,如果发现是密封胶垫往外溢出油的话,就应该立刻停下机器及时的去处理或者找修理人员过来修理。
B . How to handle
    1, check the table used in cold water , water and pipe is not smooth. If the pressure is too low , there may be blocked by the filter , if not timely to deal with , it would make the machine appear thing.
    2 , the test should be regularly NSK Bearings Hydraulic location , if you find oil pressure is too low, then it is possible to cause the cold water shut the gate.
    3, using a spoon to remove a little oil , careful observation of oil did not change the color , and then showed it to the researchers do a test to see if there is no deterioration. If you find a good place to stop the machine should be timely replacement of the oil , if the operation continues, it will bring to the machine very seriously destroyed.
    4, check the oil level is in the normal position, if there is not a normal place, and then go check the throttle there is not firmly closed . If you have already shut tight , you should fill point oil to prevent enough, if found to be sealed cushion oil spill out , then it should immediately stop the machine and timely repair personnel to deal with or find over repairs.
  评论这张
 
阅读(60)| 评论(0)
推荐 转载

历史上的今天

在LOFTER的更多文章

评论

<#--最新日志,群博日志--> <#--推荐日志--> <#--引用记录--> <#--博主推荐--> <#--随机阅读--> <#--首页推荐--> <#--历史上的今天--> <#--被推荐日志--> <#--上一篇,下一篇--> <#-- 热度 --> <#-- 网易新闻广告 --> <#--右边模块结构--> <#--评论模块结构--> <#--引用模块结构--> <#--博主发起的投票-->
 
 
 
 
 
 
 
 
 
 
 
 
 
 

页脚

网易公司版权所有 ©1997-2017