注册 登录  
 加关注
   显示下一条  |  关闭
温馨提示!由于新浪微博认证机制调整,您的新浪微博帐号绑定已过期,请重新绑定!立即重新绑定新浪微博》  |  关闭

杭州溜冰鞋

联系人:翁利文 QQ:85111570 手机:13758243050

 
 
 

日志

 
 

INA bearing after installation considerations  

2012-09-10 11:43:52|  分类: 技术 |  标签: |举报 |字号 订阅

  下载LOFTER 我的照片书  |
 

INA轴承在安装前应该注意的问题有很多相信大家都知道,但是很多人却忽略了INA轴承安装后的一些注意事项,今天在这里就给大家介绍一下INA轴承安装后的注意事项:

INA bearing is installed it should be noted that there are many believe as we all know, but many people ignored the INA bearing some notes after installation, here today to introduce you to INA bearing after installation notes:

1、对轮毂轴承单元,不要企图拆开轮毂轴承或调整轮毂单元的密封圈,否则会使密封圈受损导致水或灰尘的进入。甚至密封圈和内圈的滚道都受到损坏造成轴承的永久失效。

1, the hub bearing units, do not attempt to disassemble wheel bearing or seal ring adjustment wheel hub unit, this will prevent seal damage causing water or dust to enter. Even seals and bearings with extended inner ring raceway damage cause permanent failure.

2、装有ABS装置INA轴承的密封圈内有一个磁性推力环这种推力环不能受到碰撞、冲击或者与其他的磁场相碰撞。在安装前从包装盒中取出,让它们远离磁场,如使用的电动机或电动工具等。安装这些轴承时,通过路况测试观察仪表盘上ABS警报针,来改变INA轴承的操作。

2, equipped with ABS devices INA magnetic thrust bearing seal ring has a ring that thrust rings may be subjected to collision, impact or collision with other magnetic field phase. Before installing from the package out of the box, keep them away from magnetic fields, such as the use of electric motor or electric tools. When you install these bearings, pass the road test observation on the dashboard ABS alert-pin, to change the INA bearing operation.

3、装有ABS磁力推力环的轮毂轴承,为了确定推力环装在哪一边,可以用一个轻小的东西靠近INA轴承的边缘,轴承产生的磁力就会吸引住它。安装时将带磁性推力环的一边指向里面,正对ABS的敏感元件。注意:不正确的安装可能导致刹车系统的功能失效。

3, equipped with ABS wheel bearings of magnetic thrust rings, in order to determine which of the thrust rings mounted on the side, you can use a light small things closer to the INA bearing edges, magnetic bearing will attract it. When installing magnetic thrust side pointing to the inside of a ring, is ABS sensor. Note: incorrect installation may cause brake system failure.

4、许多的INA轴承是密封的,这类轴承在整个寿命期是不需要加润滑脂的。其他不密封的INA轴承比如双列圆锥滚子轴承在安装时必须加油脂润滑。由于轴承的内腔大小不同,所以很难确定加多少的油脂最重要的是保证轴承中有油脂如果油脂过多当INA轴承转动时多余的油脂就会渗出。一般经验:在安装时,油脂的总量要占轴承的间隙的50%。

4, a number of INA bearings are sealed, these bearings throughout the entire life of the period is not necessary and grease. Other INA bearings seals such as at the time of installation of double row tapered roller bearings must be grease lubricated. As the bearing cavity size different, it is difficult to determine how much additional oil is the most important guarantee of too much oil if the grease in the bearing when the INA bearing rotates excess grease can effuse. A general rule of thumb: at the time of installation, amount of grease to the bearing clearance of 50%.

5、安装锁紧螺母时由于INA轴承类型和轴承座的不同,扭矩的大小差别很大。注意参照有关说明。

When installing the lock nut 5, because of differences in INA bearing type and housing, torque the size varies. Reference for instructions.

 

  评论这张
 
阅读(70)| 评论(0)
推荐 转载

历史上的今天

在LOFTER的更多文章

评论

<#--最新日志,群博日志--> <#--推荐日志--> <#--引用记录--> <#--博主推荐--> <#--随机阅读--> <#--首页推荐--> <#--历史上的今天--> <#--被推荐日志--> <#--上一篇,下一篇--> <#-- 热度 --> <#-- 网易新闻广告 --> <#--右边模块结构--> <#--评论模块结构--> <#--引用模块结构--> <#--博主发起的投票-->
 
 
 
 
 
 
 
 
 
 
 
 
 
 

页脚

网易公司版权所有 ©1997-2017